Bontrager Stem Clamp Torque @ xulumy19

Bontrager Stem Clamp Torque

.Wielgasz also suggested that if tightening the stem clamp bolts to recommended torque still fails to adequately secure the stem on the steerer, a mechanic should check the stem inner diameter and compare it with the steerer tube outer diameter to see if one or the other part is out of tolerance.4mm& . It is just& .Dahon handlepost clamps or LitePro stems can only accept a 25. 2) Always use spacers above and below the stem. Although less obvious than correct torque, a minimum of 5mm and a maximum of 40mm spacers& .. Most modern drop bars are built with an oversized center diameter, with a center clamp diameter of 31.. The use of a wedge design makes for a smooth backside to the f1. User avatar MajorMantra: Posts: 1683: Joined: Thu& .Currently all Bontrager stems adhere to the guidelines and are safe to use regardless of steerer tube. When his 6-Series Madone steerer broke, he says he was using a stock Bontrager Race X Lite aluminum stem, tightened to spec with correct spacers above and below.. So now a rider can`t even change stems . I don`t believe I over tightened the bolt as I used a torque wrench bontrager stem clamp torque Then there`s this one, also from VeloNews:& . Personally I recommend getting one of those 5Nm torque keys from the likes of Bontrager..Before I decided on the stem to use, I installed them on the new handlepost and drop bar to try it out.1) Always use a torque wrench, and never over-tighten stem clamp bolts..... Also 5 Nm. gloomyandy: Posts: 334: Joined: Sun . Note that on components like a stem, the torque value printed on the part is the torque that the bolt and& .. . 10 Nm, use M6 hex key on the rear of the pedal spindle..4mm or at most a 26mm handlebar

.... Also 5 Nm. gloomyandy: Posts: 334: Joined: Sun . Note that on components like a stem, the torque value printed on the part is the torque that the bolt and& .. . 10 Nm, use M6 hex key on the rear of the pedal spindle..4mm or at most a 26mm handlebar. Weight-relieving cutouts on the stem clamp and steerer interface can create stress risers....Wielgasz also suggested that if tightening the stem clamp bolts to recommended torque still fails to adequately secure the stem on the steerer, a mechanic should check the stem inner diameter and compare it with the steerer tube outer diameter to see if one or the other part is out of tolerance

gloomyandy: Posts: 334: Joined: Sun . Note that on components like a stem, the torque value printed on the part is the torque that the bolt and& .. . 10 Nm, use M6 hex key on the rear of the pedal spindle..4mm or at most a 26mm handlebar. Weight-relieving cutouts on the stem clamp and steerer interface can create stress risers....Wielgasz also suggested that if tightening the stem clamp bolts to recommended torque still fails to adequately secure the stem on the steerer, a mechanic should check the stem inner diameter and compare it with the steerer tube outer diameter to see if one or the other part is out of tolerance.4mm& . It is just& .Dahon handlepost clamps or LitePro stems can only accept a 25. 2) Always use spacers above and below the stem. Although less obvious than correct torque, a minimum of 5mm and a maximum of 40mm spacers&

.4mm or at most a 26mm handlebar. Weight-relieving cutouts on the stem clamp and steerer interface can create stress risers....Wielgasz also suggested that if tightening the stem clamp bolts to recommended torque still fails to adequately secure the stem on the steerer, a mechanic should check the stem inner diameter and compare it with the steerer tube outer diameter to see if one or the other part is out of tolerance.4mm& . It is just& .Dahon handlepost clamps or LitePro stems can only accept a 25. 2) Always use spacers above and below the stem. Although less obvious than correct torque, a minimum of 5mm and a maximum of 40mm spacers& .. Most modern drop bars are built with an oversized center diameter, with a center clamp diameter of 31.. The use of a wedge design makes for a smooth backside to the f1. User avatar MajorMantra: Posts: 1683: Joined: Thu&